Forum GLPI-Project

netix

Member

Registered: 2009-10-16

Posts: 8

Tracker Plugin and AlliedTelesis switch

I have a problem with tracker and AlliedTelesis stackable switch AT 8000s
snmp model are switch generic
and it does not connect anyone

Last edited by netix (2009-11-03 12:25:16)

ddurieux

Plugins Dev

From: Propières, France

Registered: 2005-06-17

Posts: 7,521

Re: Tracker Plugin and AlliedTelesis switch

So this manufacturer switchs are not been yet coded in Tracker.

I have receive your mail. It's a little complicated. We must see on switch snmp how it use vlans (like Cisco or like HP) because code is very different for connections on each port

netix

Member

Registered: 2009-10-16

Posts: 8

Re: Tracker Plugin and AlliedTelesis switch

We must see on switch snmp how it use vlans (like Cisco or like HP) because code is very different for connections on each port

Just say how can I help you ..

ddurieux

Plugins Dev

From: Propières, France

Registered: 2005-06-17

Posts: 7,521

Re: Tracker Plugin and AlliedTelesis switch

Like you have say me in mail, you have only one vlan, so in this case, I there is no problem but if other have many vlan, it's possible it not work.

caillet.melanie

Member

Registered: 2013-06-19

Posts: 4

Re: Tracker Plugin and AlliedTelesis switch

Hello,

I have, at the moment even, this problem. In my computer equipment, I have switchs Allied Telesis. During the inventory, I have information such as the name of the switch etc. but when I look in the tab FusInv SNMP, I see that I have fasts which have connections but I do not see which computer is connected on this port(bearing).

Would you have a solution my problem?

I know that this comment is old but I do not find solution for my problem and it has been now more than a week since I look for information on the Internet to solve him(it) but in vain.

Best Regards, Mélanie.

ddurieux

Plugins Dev

From: Propières, France

Registered: 2005-06-17

Posts: 7,521

Re: Tracker Plugin and AlliedTelesis switch

Give the sysdescr.
Have you too the LLDP activated in the switch?

caillet.melanie

Member

Registered: 2013-06-19

Posts: 4

Re: Tracker Plugin and AlliedTelesis switch

I have two materials Allied:
Allied Telesis AT-9924SP version 2.9.1-05 20-Apr-2007
ATI AT-8000S

I tried to get back the MIB both Allied whom I put in the SNMP models creation but nothing changes. I do not know how to make.

No I did not activate the LLDP on my switchs.

ddurieux

Plugins Dev

From: Propières, France

Registered: 2005-06-17

Posts: 7,521

Re: Tracker Plugin and AlliedTelesis switch

It's better to have LLDP

caillet.melanie

Member

Registered: 2013-06-19

Posts: 4

Re: Tracker Plugin and AlliedTelesis switch

All right. What are the commands(orders) the most important to put on my switch so that I can obtain the information which I need?

I would have to know which computer is connected on which port(bearing) of the switch.

At the moment, I know which port(bearing) of the switch is connected or not then I have, on the port(bearing) ch1 all a list of computers and switchs which goes back up(raises) but I shall want to know on which switch they are really and especially on which port(bearing).

While waiting for an answer from you, I wish you a good day.

caillet.melanie

Member

Registered: 2013-06-19

Posts: 4

Re: Tracker Plugin and AlliedTelesis switch

Hello,

I activated the LLDP on all my switchs, I redid a network inventory and I always have the same problem.

Could you help me please? I shall like having solved this problem before ending my company internship.

Thank you in advance.

ddurieux

Plugins Dev

From: Propières, France

Registered: 2005-06-17

Posts: 7,521

Re: Tracker Plugin and AlliedTelesis switch

not normal, can you send me a snmpwalk of one of your switch?